En México: 01800-953-00-93
Correo de Ventas:ventas@mx.omega.com

Pneumatic Angular Grippers 180°

DCT-RE Series Angular 180° Gripper with Spring Assist

Grippers, Angular Grippers | DCT-RE Series  Angular 180° Gripper with Spring Assist

Grippers, Angular Grippers

MXN33,200.00 DCT-12M-RE

  • Highly Configurable Modular Automation— Exclusive Direct Connect™ Robohand Technology Provides Multiple Mounting Options
  • Full Jaw Opening (180°) Allows Part to be Direct Fed into Gripper, Eliminating One Additional Motion
  • Fail Safe Operation-Internal Spring to Maintain Gripper Force if Gripper Looses Air Pressure
  • Compact Design for Use in Confined Spaces
  • Shielding to Repel Chips for Use in Harsh Environments
  • Precission Gripper - Repeatability ±0.05 mm (0.002") and Accuracy of ±0.07 mm (0.0028")
  • Up to 5 Million Cycles in Typical Applications and 10 Million with Maintenance
  • Temperature Rating from -35 to 80°C (-30 to 180°F)
  • System Requires 4 to 7 bar (60 to 100 psi) Dry Filtered (40 Microns or Better) Air Supply
  • Accessory Equipment Required – 4-Way 2-Position Pneumatic Control Valve
Movimiento - Ver Productos Relacionados

Descripción


DCT-RE Series Pneumatic Grippers are angular grippers with a spring assist. This Fail Safe spring allows the gripper to retain the component should the air pressure supply fail, it also allows the gripper to be used with a single acting mode. DCT-RE pneumatic grippers have a 180° jaw opening allowing complete release of a directly fed part. Gripper forces ranges from 40 N (9 lbs) to 141 N (32 lbs). These angular grippers are compact and designed for confined spaces, but consideration must be given to allow for the additional space required for the rotating jaws. The adjustable stop accessory (BR) will help to reduce the space requirement by restricting the open position. Standard mounting is from the top, but the gripper can also be mounted from the back of the body and will operate in any direction. Each jaw has a useful rotational stroke of 90° for a full 180° opening and there is a over-stroke of approximately 1.5° before reaching the fully gripped position. Jaws have to be designed to close for a grip of 0° gripping position (parallel jaws).

Harsh Environments are no problem for this gripper due to the shielding that repels chips and other particulate from the internal drive mechanism.

Note: To limit shocks at the end of the opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow control valves make it possible to reduce the rotation speed and are highly recommended.

Pnuematoc linear motion automation components are double acting air cylinders that require a dry air supply with filtering to 40 microns or better. For best control of pneumatic components, flow control valves (regulating out) should be installed to regulate the speed of the device. Position sensors can easily be added to motion components to detect the end of travel positions of the slides, they are the standard method of communication with the PLC and are available in inductive or magneto resistive sensing styles and come in both PNP or NPN sourcing signals.

PNEUMATIC SPECIFICATIONS IMPERIAL METRIC
Pressure Operating Range: 4 to 7 bar(60 to 100 psi)
Cylinder Type: Double acting
Dynamic Seals: Internally lubricated Buna-N
Valve Required to Operate: 4-way, 2-position
AIR QUALITY REQUIREMENTS
Air Filtration: 40 Micron or better
Air Lubrication: Not necessary*
Air Humidity: Low moisture content (dry)
TEMPERATURE OPERATING RANGE
Buna-N Seals (Standard): -35 to 80°C (-30 to 180°F)
FKM Seals (Optional): -30 to 150°C (-20 to 300°F)
MAINTENANCE SPECIFICATIONS
Expected Life Normal Application: 5 million cycles w/preventative maintenance 10+ million cycles*
Field Repairable: Yes
Seal Repair Kits Available: Yes
* Addition of lubrication will greatly increase service life.

SPECIFICATIONS DCT-12M-RE
Total Rated Grip Force, F @ 7 bar (100 psi) L = 25 mm (1") @ 0°: 40 N (9 lb)
Stroke: 90° of stroke for each finger
Weight: 0.12 Kg (0.26 lb)
Pressure Range: 4 to 7 bar (60 to 100 psi)
Cylinder Bore Ø: 12 mm (0.472")
Displacement: 1.92 cm3 (0.117 in3)
TEMPERATURE RANGE
Standard Seals: -35 to 80°C (-30 to 180°F)
FKM Seals: -30 to 150°C (-20 to 300°F)
Actuation Open/Close: 0.08/0.05 sec
Accuracy: ±0.07 mm (±0.0028")
Repeatability: ±0.05 mm (±0.002")
Valve Required to Actuate Single Acting: 3-way, 2-position
Valve Required to Actuate Double Acting: 4-way, 2-position


SPECIFICATIONS DCT-16M-RE
Total Rated Grip Force, F @ 7 bar (100 psi) L = 25 mm (1") @ 0°: 87 N (19 lb)
Stroke: 90° of stroke for each finger
Weight: 0.20 Kg (0.44 lb)
Pressure Range: 4 to 7 bar (60 to 100 psi)
Cylinder Bore Ø: 16 mm (0.630")
Displacement: 4.12 cm3 (0.251 in3)
TEMPERATURE RANGE
Standard Seals: -35 to 80°C (-30 to 180°F)
FKM Seals: -30 to 150°C (-20 to 300°F)
Actuation Open/Close: 0.15/0.12 sec
Accuracy: ±0.07 mm (±0.0028")
Repeatability: ±0.05 mm (±0.002")
Valve Required to Actuate Single Acting: 3-way, 2-position
Valve Required to Actuate Double Acting: 4-way, 2-position


SPECIFICATIONS DCT-20M-RE
Total Rated Grip Force, F @ 7 bar (100 psi) L = 25 mm (1") @ 0°: 141 N (32 lb)
Stroke: 90° of stroke for each finger
Weight: 0.33 Kg (0.73 lb)
Pressure Range: 4 to 7 bar (60 to 100 psi)
Cylinder Bore Ø: 20 mm (0.787")
Displacement: 7.92 cm3 (0.483 in3)
TEMPERATURE RANGE
Standard Seals: -35 to 80°C (-30 to 180°F)
FKM Seals: -30 to 150°C (-20 to 300°F)
Actuation Open/Close: 0.20/0.14 sec
Accuracy: ±0.08 mm (±0.003")
Repeatability: ±0.05 mm (±0.002")
Valve Required to Actuate Single Acting: 3-way, 2-position
Valve Required to Actuate Double Acting: 4-way, 2-position
Hacer Pedido(Especifique el Número de Modelo)

Lo que han comprado otras personas: Cuando vea este icono, haga clic sobre él para abrir la lista de productos que otras personas han comprado al adquirir este modelo

Número de parte/Desc.
Cant.
Descripción
  
DCT-12M-RE
MXN33,200.00
Disponible en: 12 Semanas
 
180° Series Angular Pneumatic Gripper with spring assist, 18 mm (0.71') jaw opening
  
DCT-16M-RE
MXN44,305.00
Disponible en: 12 Semanas
 
180° Series Angular Pneumatic Gripper with spring assist, 20 mm (0.79') jaw opening
  
DCT-20M-RE
MXN41,410.00
Disponible en: 12 Semanas
 
180° Series Angular Pneumatic Gripper with spring assist, 22 mm (0.87') jaw opening
Accessories
  
OISP-014
MXN7,625.00
Disponible en: Disponible
 
4 mm PNP inductive sensor with quick disconnect, 1 or 2 required
  
OISN-014
MXN7,225.00
Disponible en: Disponible
 
4 mm NPN Inductive sensor with quick disconnect, 1 or 2 required
Haga clic para abrir la lista de productos que otras personas han comprado al adquirir este modeloOHSP-017
OHSP-017
MXN7,445.00
Disponible en: Disponible
 
PNP magneto resistive sensor long barrel with quick disconnect, 1 or 2 required
Haga clic para abrir la lista de productos que otras personas han comprado al adquirir este modeloOHSN-017
OHSN-017
MXN4,990.00
Disponible en: Disponible
 
NPN magneto resistive sensor long barrel with quick disconnect, 1 or 2 required
  
OHSP-011
MXN6,910.00
Disponible en: Disponible
 
PNP magneto resistive sensor short 90° barrel with quick disconnect, 1 or 2 required
  
OHSN-011
MXN4,990.00
Disponible en: 12 Semanas
 
NPN magneto resistive sensor short 90° barrel with quick disconnect, 1 or 2 required
Haga clic para abrir la lista de productos que otras personas han comprado al adquirir este modeloCABL-010
CABL-010
MXN1,710.00
Disponible en: Disponible
 
Quick disconnect cable 2 m (6') in length, 1 or 2 required
  
CABL-013
MXN2,960.00
Disponible en: 12 Semanas
 
Quick disconnect cable 5 m (16') in length, 1 or 2 required
  
BR-CT-12
Consultar Ventas  
Disponible en: 
 
 
Adjustment stop kit (1 stop and 1 shielded plate) for DCT-12M-RE, 1required
  
BR-CT-16
MXN2,350.00
Disponible en: 12 Semanas
 
Adjustment stop kit (1 stop and 1 shielded plate) for DCT-16M-RE, 1 required
  
BR-CT-20
MXN2,620.00
Disponible en: 12 Semanas
 
Adjustment stop kit (1 stop and 1 shielded plate) for DCT-20M-RE, 1 required
  
SD-CT-16
MXN3,265.00
Disponible en: Disponible
 
Inductive sensor mounting kit for DCT-16M-RE, 1 or 2 required
  
SD-CT-20
MXN3,265.00
Disponible en: 12 Semanas
 
Inductive sensor mounting kit for DCT-20M-RE, 1 or 2 required
Todas las cantidades que se muestran en MXN
Nota: Sensor and cable sold separately. Inductive sensor not available on DCT-12M-RE.
Ejemplo de pedido: (1) DCT-12M-RE 180° Series pneumatic angular gripper with spring assist,18 mm (0.71'') jaw opening and gripper force of 40 N (9 lb), MXN33,200.00
We noticed you are from the US. Visit your local site for regional offers and live support.