Sensor de Flujo de Dispersión Térmica

FSW-6000 and FSW-7000 Series

^MXN25,975.00 FSW-6212

HACER PEDIDO

Fácil de instalar
Sin piezas móviles - Fiabilidad en la Exención de mantenimiento
Excelente compensación de temperatura - no se ve afectada por los gradientes de temperatura
Puede funcionar en temperaturas de hasta 120 ° C (248 ° F) con la Opción Salud
Presión máxima de operación de 300 Bar (4300 psi)
Juego de 8 LEDs Integrados à la Tasa de Flujo / Indicación de Punto de ajuste
Puede ser utilizado como interruptor de nivel

Interruptores, caudalímetros de área variable y caudalímetros de área variable - Ver Productos Relacionados

Descripción

The FSW-6000/7000 Series are thermal flow switch monitors designed to monitor flow status and also used to detect level of liquids, air and gas. A chain of 8 LED’s gives the user a visual indication of the flow rate. In addition, there isalso a dichromatic LED, which shows the switch point status of the unit. The sensing element and connection of the FSW-6000/7000 Series are made with 316 SS. The standard enclosure is glass-filled nylon and is also available in an aluminum enclosure for hazardous environments. The FSW-6000/7000 Series can be made with a great variety of process connections such as threaded, flange, or sanitary.

The FSW-6000/7000 Series line of thermal flow switch monitors is based on the principle of thermal dispersion. A typical configuration uses two platinum Resistance Temperature Detectors (RTD’s) set within the tip of the sensor. One RTD is heated a few degrees above the temperature of the medium and the other RTD is used as a reference, sensing the actual process temperature. The second RTD also monitors the temperature of the medium, as any changes in temperature must be compensated for in the first RTD. As the process medium flows over the tip of the sensor it disperses some of theheat from the first RTD. The temperature change between the two RTD''s signals the probe’s electronics and the switch changes state once the set point has reached.

The FSW-6000/7000 Series may be installed in a pipe or tank using the thread or connection provided. Use only the hexagon when tightening to achieve a seal, do not use the body. The body should be rotated after tightening to leave the cable gland in suitable orientation. The FSW-6000/7000 Series is not affected by its fixing position so it may be installed at any angle around the pipe. However, it is recommended that with horizontal pipe runs the sensor should be installed on the side, into the middle of the pipe. In vertical pipes, the FSW-6000/7000 Series should be installed when there is flow in an upward direction against gravity. Care should be taken when installing the sensor that the probe extends clear of the pipe’s internal wall and is fully immersed into the flow. In pipes with smaller diameters, some care should also be taken so that the sensor is not screwed too far into the line.

SPECIFICATIONS
Accuracy: ±10% of setpoint
Repeatability: ±1% of setpoint
Power Supply:
    FSW-6000: 85 to 240 Vac (50/60 Hz)
    FSW-7000: 24 Vdc ±10%
Temperature Range:
    Process: -20 to 80°C (-4 to 176°F) [sanitary option to 120°C (248°F) for CIP]
    Operating: -20 to 60°C (-4 to 140°F)
Max Pressure: 300 bar (4351 psi)
Protection Class: NEMA 4 (IP65)
Wetted Materials: 316 SS
Enclosure Material: Glass filled nylon standard or aluminum die cast option
Process Connection: ½ to 1½ NPT, Tri-Grip™, or flange (others available, consult Flow Engineering Department)
Output: 250 Vac SPDT 5 A relay
Switch Point Adjustment: Potentiometer
Bargraph:
    Green LED: Flow rate above setpoint
    Yellow LED: Flow is at above setpoint
    Red LED: Flow is below setpoint
Switch Point Status:
    Red LED: No flow
    Green LED: Flow
Response Time: 1 to 10 seconds
Max Start up Delay: 12 seconds
Switching Range: 3 cm/s to 3 m/s (0.09 to 9.84 ft/sec) (liquid), 5 cm/sec to 15 m/sec (0.16 to 49 ft/sec) (gas)
Dimensions:
    Nylon Head: 88 Dia x 80 mm H (3.5 x 2.5" H)
    Aluminum Head: 88 Dia x 108 mm H (3.5 x 4.25")
    Insertion Length: 1³⁄8, 2 and 3" standard, for other lengths consult Flow Engineering
     Maximum insertion Length is 36"

    Weight: Approx 680 g (1.5 lb)

Hacer Pedido(Especifique el Número de Modelo)

Lo que han comprado otras personas: Cuando vea este icono, haga clic sobre él para abrir la lista de productos que otras personas han comprado al adquirir este modelo

Número de parte/Desc.

Cant.

Descripción

FSW-6212

MXN25,975.00

Disponible en: 6 Semanas

85 to 240 Vac, 3/4 NPT, 2" length, glass filled nylon with 1/2 NPT conduit, cable gland, and 2 m (6.5') cable. For 1" to 4" pipes

FSW-6222

MXN24,490.00

Disponible en: 6 Semanas

85 to 240 Vac, 3/4 NPT, 2" length aluminum die cast with 1/2 NPT conduit, and 2 m (6.5') cable. For 1" to 4" pipes

FSW-6512

MXN28,445.00

Disponible en: 6 Semanas

85 to 240 Vac, 1-1/2 Tri-Grip™, 2" length, glass filled nylon with 1/2 NPT conduit with cable gland, and 2M (6.5') cable. For 1 to 4" pipes

FSW-7111

MXN25,975.00

Disponible en: 6 Semanas

24 Vdc, 1/2 NPT, 35 mm (1 3/8") length, glass filled nylon with 1/2 NPT conduit with cable gland, 2m (6.5') cable. For pipes up to 1"

FSW-7112

MXN21,480.00

Disponible en: 6 Semanas

24 Vdc, 1/2 NPT, 50 mm (2") length, glass filled nylon with 1/2 NPT conduit with cable gland, 2m (6.5') cable. For 1" to 4" pipes

FSW-7121

MXN24,490.00

Disponible en: 6 Semanas

24 Vdc, 1/2 NPT, 35 mm (1-3/8") length, aluminum die cast with 1/2 NPT conduit, 2 m (6.5') cable. For 1" to 4" pipes

FSW-7122

MXN24,490.00

Disponible en: 6 Semanas

24 Vdc, 1/2 NPT, 50 mm (2") length, aluminum die cast with 1/2 NPT conduit, 2 m (6.5') cable. For 1" to 4" pipes

Accessories

70A-1

MXN1,270.00

Disponible en: Disponible

Continuous tone alarm

TX4-100

MXN1,575.00

Disponible en: Disponible

30.5 m (100') spool of 4 Conductor Wire

U24Y175

Consultar Ventas

Disponible en:

24 Vdc power supply

Todas las cantidades que se muestran en MXN
Nota: Comes complete with operator’s manual.

For "ECTFE/ETFE" element coating, add suffix "-ETFE" to model number, add $200 to price.

Ejemplo de pedido: (1) FSW-6212 Flow Switch, MXN25,975.00 plus (1) FSW-6212 Flow Switch, MXN25,975.00, MXN25,975.00 + 25,975.00 = MXN51,950.00

Generador de Número de Parte

Construya su Número de Parte Abajo

	(1)	(2)	(3)	(4)
FSW-

Opciónes de Descripción:

(1) Power seleccionar de:
6 para 85 to 240 Vac
7 para 24 Vdc ± 10%

(2) Process Connection seleccionar de:
1 para 1/2 NPT thread
2 para 3/4 NPT thread
3 para 1 NPT thread
5 para 1-1/2" Tri-Grip
6 para 2" ANSI flange

(3) Enclosure seleccionar de:
1 para Glass filled nylon with 1/2 NPT conduit and cable gland
2 para Aluminum die cast with 1/2 NPT conduit
3 para Aluminum die cast with cable gland

(4) Insertion Length seleccionar de:
1 para 35 mm (1-3/8")
2 para 50 mm (2")
3 para 75 mm (3")

Nota: Todas las combinaciones pueden no ser válidas, revise la hoja de especificaciones para números de parte válidos

Manuales de Productos:

Descarga FSW-6000/FSW-7000 Series - Thermal Dispersion Flow Switches