|
|
 |
|
|
|
|
|
|
|
| • |
Networks Stepper Drives (1240i, 3540i, Si3540, ST series, STAC6 series, STM23 series) for Multi-Axis Motion Applications
|
| • |
Programmable with Easy-to-Use SiNet Hub Programmer™
|
| • |
4 Optically Isolated Inputs, 5 to 24 Vdc
|
| • |
4 Optically Isolated Outputs, 24 Vdc, 100 mA
|
| • |
Hub Programs and Host Computers Also Have Access to the I/O in Each Drive
|
| • |
Powered by Drive #1, No External Power Supply Required
|
| • |
Compatible with MMI-01 (Operator Terminal)
|
| • |
Communication via RS232
|
| • |
Sample Motion Programs Available by Request
|
View related products - Drives & Motors
|
| |
|
|
|
 |
The SiNet™ Hub 444 allows up to 4 Stepper
or Servo Si™ drives to be controlled in host
mode from a single PC or PLC’s RS232
serial port or will run in stand-alone mode.
Each indexer-drive acquires its unique address
from the port to which it is connected. This simple addressing scheme
minimizes the cost of the drives, and more
importantly, the cost of configuring and/or
replacing drives in your system. Connections
are made with low cost, reliable RJ11 cabling.
Any of our popular, cost effective
programmable Stepper or Servo Si™ drives or
Si™ motor controls can be used with the
SiNet™ Hub 444. By choosing the power level
and features you need for each axis
of your application, SiNet™ can provide a
cost effective single or multi-axis motion
solution. The SiNet™ Hub 444 is powered by
the drive that’s connected to port #1, saving
you the cost and installation expense of
using a separate power supply. Our
Si Command Language™ (SCL) allows a
host PC or PLC to execute relative, absolute
and homing moves, make status inquiries,
sample inputs, set outputs, and more.
If your application requires a single axis to
operate in "host mode", you can connect any
of our programmable Si™ drives directly to
your PC via the SiNet™ Hub 444 and invoke
the Si Command Language™ (SCL).
SCL allows for control via serial commands sent from a host device such as a PC or PLC. This permits the user to perform a variety of motion, I/O, and system
status tasks in real time via a host serial device.
Our SiNet Programmer™ Windows software allows the
user to create and store multi-axis motion
control programs in the SiNet™ Hub 444
and run them without a PC, thus allowing
the user to create a complex multi-axis
motion system controlled from an operator
interface or trigger.
|
| |
|
|
|
|
|
† All dollar amounts on this site are shown in US currency.
Note: Software and drive cables are included.
|
|
|
|
|
| |
| Related Links -
Manual, Related Products
|
| Product Manual |
| Download HUB444 - Motion Control Network Hub |
| Download STM, ST, Stac6, 1240i, 3540i, si3540 Series - Si Command Language (SCL) for Stepper Drives |
| Related Products |
|
|
|
|
 |
STM Series: |
| Integrated Stepper Drives/Motors with Advanced Features and Control Options |
|
|
 |
1240i: |
| Programmable Step Motor Indexer/Drive |
|
|
 |
3540i: |
| Programmable Step Motor Indexer/Drive |
|
|
 |
ST Series: |
| High Performance Stepper Drives With Advanced Features And Control Options |
|
|
 |
Si3540: |
| Programmable Stepper Drive with Integrated Power Supply |
|
|
 |
STAC6 Series: |
| High Performance Stepper Drives with Integrated Power Supply |
|
|
|
|
|
|
|
|
